The homeline processing machine should provide the site and power supply that meets the requirements, and there is sufficient turnover venue and space. There is no other vibration interference in the venue. When the winding operation is winding, the operator needs to test the winding quality of the coil. It is essential. The bus processing machine is equipped with a precise control system and electrical appliances. High -quality power supply is the fundamental guarantee for the normal work of the bus processor.

The overall frame structure is welded from left and right columns, beams, and front and rear support. Its rigidity and high accuracy stability. The upper part of the left and right columns is welded to fix the left and right oil cylinders, and the left and right support bottom iron is installed in the lower part of the column to increase the contact area at the bottom and prevent the CNC bending machine from dumping during the consignment process. You can remove it after the machine is installed. The working principle and product introduction of the resistor bus

The automatic winding tie -tie machine workbench and foundation should have sufficient strength and stiffness to avoid severe vibration when the automatic winding tie machine is moving at high speed, and ensure that the vibration of the winding tie machine will not affect its own accuracy and life. It does not affect the quality of the coil, and the nearest equipment and buildings do not have a bad impact on the winding tie machine.

There is an oil thermometer in the bus processor, which indicates the oil temperature of the top layer of the transformer. When the transformer is 40 ° C at 40 ° C during the operation, its temperature rise shall not exceed 55 ° C. During the operation, the top layer of oil temperature shall prevail, and the temperature rise is the reference data. The temperature ascending standards of transformers in my country are based on the ambient temperature of 40 ° C, so the oil temperature of the top layer of the transformer must not exceed 40 ° C + 55 ° C = 95 ° C. If the temperature of the top layer is more than 95 ° C, the temperature of the internal coil will exceed the heat resistance of the coil insulation. In order to make the insulation do not cause too fast aging, the surveillance of the top layer of the top layer of the transformer should be controlled below 85 ° C. The cooler is abnormal or the failure such as the oil pump is stopped, the fan is damaged, the heat dissipation pipes accumulate, the cooling efficiency is poor, and the radiator valve is not opened. The cooling system should be maintained in time to maintain, rinse or throw a spare cooler, otherwise the load of the transformer must be adjusted. The temperature indicator has an error or instructions to fail, and the temperature table should be replaced.

The working principle of the resistor bus is an oil thermometer in the product briefing bus processor, which indicates the oil temperature of the top layer of the transformer. When the transformer is 40 ° C at 40 ° C during the operation, its temperature rise shall not exceed 55 ° C. During the operation, the top layer of oil temperature shall prevail, and the temperature rise is the reference data. The temperature ascending standards of transformers in my country are based on the ambient temperature of 40 ° C, so the oil temperature of the top layer of the transformer must not exceed 40 ° C + 55 ° C = 95 ° C.

The CNC busbar bending machine is suitable for welding transformers under various working conditions: the welded transformer is poured with a vacuum -made epoxy resin, and the secondary internal water is forced to cool down. Therefore, it has good moisture -proof, shock -proof and dustproof performance. The insulation can reach F -grade. The power output is strong and stable. CNC's parent line machine -guided magnet structure is specially designed. It is made of high -guide magnetic materials. The air load loss is extremely small, high efficiency, energy saving and power saving, which is conducive to reducing production costs.

Because it is arc -shaped, its blade cannot be made into a rectangular, but it should be made into sharp corners, so the force of the blade is not ideal, and the blade damage is more powerful. The shear tool factory. The slug -type hydraulic shear machine overcomes all the above problems. However, there are not many domestic manufacturers who can do the gate shear machine. The working principle and product introduction of the resistor bus

Which of the bus processing machine is better in Jinan? Which one should we choose in many bus processing machine manufacturers? When we buy the homeline processing machine, we should first consider the quality of the bus processor to pass, and then we must consider the service of the product. The service here refers to the pre -sale and after -sales service. Service thoughts are in place. In the end, we have to consider product prices.