What is the cost of the copper row bending machine (quotation of Beijing portable mother row machine)

With the continuous renewal and development of science and technology, the bus processing machine is now widely used in the equipment of the electrical setting industry. In order to improve the work efficiency of the bus processing machine and ensure the safety of operation, it is very important to understand how to properly operate the bus processing machine. The following editors will introduce you in detail with many years of industry experience.

The cost of the copper volume bending machine is how many full -automatic parent line machines are used by the factory setting and configuration after purchasing the device. Some customers need to change the position and function of the parent machine machine to meet their own production. In design and manufacturing, the parent line machine generally leaves a certain amount of space for easy maintenance, replacement parts, etc. The use of this waste can make certain improvements, but all improvements must be within the maximum value allowed by the device. Modification equipment will damage the device.

First of all, we need to set the positioning position. What is the starting position? Simply put, it is the starting point of starting the winding on the skeleton. This position is closely linked to the beginning of the coil and the type of coil. The specific values of the correlation positions that comes with the measuring function are measured; the operator can also use manual measurement to measure it, using the fixed point as the reference point to use the ruler to actively measure, and pay attention to the wrapping direction of the coil when setting this point.

The punching station of the CNC busbar machine (patented design, imitation must blame): The turntable design, the disc (mold frame) built four parsing of the punch, the commonly used mounting does not need to be replaced with one and one. The light source is convenient to change the mold. When working at work, the insurance button is easy to rotate the disc (mold shelf) in place. Compared with similar products, the cost of molds is low; This equipment device reduces unnecessary damage to the mold changing mold;

In order to ensure the mechanical accuracy of the fully automatic bus system, it is important to emphasize that the same axis of the fixed seat and the holding mechanism, the tail seat and the tail seat holding mechanism are The same axis of a fixed seat. What is the cost of copper row bending machine?

In addition, if the rotation center of a pulley, gear, bearing, or rotor is deviated from the geometric center line, it will appear eccentric. Due to the strict horizontal displacement calibration when the company's parent line machine is produced, the general phenomenon that generally does not appear on the old machine. The neutrality of the machine is very important because it increases because it increase The rotation force applies abnormal stress on the bearing and sealing parts. The types of wrong are: Parallel is not right, the angle is not right, parallel, and angle. Typical wrongdoing is mainly caused by the following reasons: inaccurate assembly of the original component, such as motors, pumps, etc.; The relative position of the original components after installation moves; the twist deformation caused by the pressure of the pipeline system; Flexible support is distorted; the machine deformation caused by temperature changes; the coupling surface is not perpendicular to the axis; because the ground base flexibility is too large, the machine moves when the machine is tightly fixed. In fact, most of the cases are not the combination of the axis angle that is not right to the middle of the peace. The general principle is that the diagnosis should be judged according to the increase of 1x speed in the direction of axial and vertical (or horizontal), and the changes in the vibration level at the corresponding 2X are judged.

How much is the cost of the copper row bending machine? , Acrylic, LED/Neon light groove -shaped, pore -shaped literal cutting, plastic light box molds.

In response to the slow and smoothness of the main axis speed requirements at 0 ～ 50R/min, the following design plans are proposed: ① According to the principle of mechanical transmission, the motion method with a synchronized band 2 transmission is used to change the speed ratio and reduce the start speed as much as possible. ② In the previous design, a polar motor with a rated speed of 2800R/min was used. However, after a period of operation, the starting speed (by the spindle of the winding) was not adjusted by 0 slowly and uniformly. Instantly acceleration will be pulled off. Try the wire material. After that, the tetrassis motor YS6334 with a rated speed of 1400R/min was used. The parent wire uses the inverter to control the motor as the driver, which effectively ensures the stable control of the motor at a low -speed state at a low speed.